|
Post by tkrueger3 on Jul 5, 2009 23:24:49 GMT -5
My first batch from my new Covington vibe. I started with a bunch of quartz, agate, and amethyst that I had already done the 60/90 grit in the rotary. Started in the vibe with 220. Mistake, I now know. As time went on, had to keep adding stuff to get the volume needed to let the action work right. Put a bunch of "leftovers" from the WF in, some odds and ends, and let it rip. Here's what's left after a full week of twice-daily fidgeting with it, 4 days of final polishing, first with AO, then with CO, plus, of course, Borax between loads and included with the CO. Some of it looks ok, some not, but I sure learned a lot. Here's the whole load: A pile of amethyst (my camera will NOT catch the colors right) I tossed these 3 preforms in for fun - 2 amethyst and 1 amazonite: This little guy was a surprise - the bubble on the ridge flashes a bright violet or lavender chatoyancy. Don't know what the rock is - heck, I hardly know what any of them are! A bunch of various agates: Some (I think) green moss agate and some green aventurine: A pile of quartz: A couple of wee quartz chunks that seem to have flecks of gold included, and give a brilliant golden flash: I think this may be moonstone (what do I know?) I tried to catch some of the colorful flashes, but didn't do too well: And ALL of this filler was in there, too! Thanks for looking, pardon the cruddy photography, and I would appreciate any ID's that may come across. Tom
|
|
|
Post by frane on Jul 6, 2009 6:21:30 GMT -5
I think for a first tumble you did pretty good! I suspect your photo colors are a bit off so it is hard to help identify anything for you but you did catch a good flash in the possible moon stone. Amazonite can be the same color as your moonstone so it is hard to tell from here. Aventurine is a difficult one to get a good solid shine on. All the mica make some soft spots that will give problems, especially in a mixed load. I suspect you have some very nice shine on a lot of them but my eyes just can't see as well as they used to. Looks like your preforms turned out great! I think you did wonderful though! Now, time for that next batch! ;D Fran
|
|
|
Post by tkrueger3 on Jul 6, 2009 8:53:47 GMT -5
About the photos - my "real" camera is trying to expire - it won't do macro photos any more, and anything purple comes out blue, and it doesn't like to focus on anything closer than, say, 10 feet ..... anyway, I wound up using the camera in my cell phone. No flash, no adjustments, no zoom, just your basic 3.2mp digital point-n-shoot. Somebody give me a new camera for my birthday, please? ;D
|
|
|
Post by MyNewHobby on Jul 6, 2009 19:50:55 GMT -5
Very nice first batch!!!! Oh so much better than my first!!! ;D
Julie
|
|
|
Post by tkrueger3 on Jul 6, 2009 23:30:49 GMT -5
Thanks, Julie - they aren't great, but I've sure learned a lot! Over half of them are destined to be broken up/sawed up and run through all over again. The rest are destined to decorate a small glass bowl or little wine glass or something like that. Next run, I'll sure know not to mix hardnesses (is that a word?) together in the same batch. My current project, while I have 4 rotating barrels going with new rough, is to start teaching myself to wrap, going with the various tutorials available on this board. (Already I like it, but already I know I have to find new ways to make my old fat arthritic fingers and feeble eyes do it right.) Tom
|
|
|
Post by Jack ( Yorkshire) on Jul 7, 2009 2:36:26 GMT -5
A Nice Batch and a good finish
Don't worry if they don't all polish up well the Ammy is great this shows you are doing the job right (if you had cross contamination this would be cloudy/Scratchy)
Pre forms come out brilliant I do quite a lot, and you can experiment at to how sharp a bevel you want left as to which stage you put them in OR when you do the bevel
Great Job
Thanks for showing
Jack Yorkshire uk
|
|