|
|
Post by miket on Mar 13, 2020 10:28:08 GMT -5
Not sure how you wrap this kind of triangle shaped cab, this is what I came up with. It actually hangs well but it makes the design tilt a little to the left. Any suggestions on how else I could have done it? Thanks for looking.   |
|
|
|
Post by knave on Mar 13, 2020 10:33:19 GMT -5
I’m a fan of this wonkiness.
|
|
|
|
Post by opalpyrexia on Mar 13, 2020 11:00:06 GMT -5
Nice! Don't worry, be happy!
|
|
|
|
Post by knave on Mar 13, 2020 12:42:10 GMT -5
It actually hangs well but it tilts a little to the left. Biting my tongue here |
|
|
|
Post by mohs on Mar 13, 2020 13:36:13 GMT -5
double r  ler comments nice to see other cabs that don't cooperate always tweaking hearts if a specif gravity is more than the other side say a granite gneiss combo gotta tweak the pin or tweak grind that side to lean properly depending on the political environment mostly |
|
|
|
Post by RocksInNJ on Mar 13, 2020 15:08:10 GMT -5
I like it and wouldn’t worry about it.
|
|
|
|
Post by hummingbirdstones on Mar 13, 2020 20:04:10 GMT -5
I think it looks fine, Mike.
You did what you could by pulling that left side wire in a bit more to balance it. Triangles that don't have 2 symmetrical sides are real tough to wrap. You did a good job on this one!
|
|
|
|
Post by miket on Mar 13, 2020 22:08:36 GMT -5
I think it looks fine, Mike.
You did what you could by pulling that left side wire in a bit more to balance it. Triangles that don't have 2 symmetrical sides are real tough to wrap. You did a good job on this one!
Thanks Robin, I appreciate it! |
|
|
|
Post by rockjunquie on Mar 14, 2020 8:42:04 GMT -5
I think it looks fine. Not all cabs are perfect. You did a good job pulling the bail over a little without it being a big deal. Alternatively, you could have flipped the top around, but that wouldn't do much for the pattern. I will say, and I hate to be picky, but the wire holding the stone on the right could be tweaked a little. Looks bent and uneven with the other side. But, my eye always picks up on that sort of thing. It's not a big deal.
|
|
|
|
Post by miket on Mar 14, 2020 10:18:43 GMT -5
I think it looks fine. Not all cabs are perfect. You did a good job pulling the bail over a little without it being a big deal. Alternatively, you could have flipped the top around, but that wouldn't do much for the pattern. I will say, and I hate to be picky, but the wire holding the stone on the right could be tweaked a little. Looks bent and uneven with the other side. But, my eye always picks up on that sort of thing. It's not a big deal. Thanks Tela. I might have been able to do a better job on the cab, that probably would have made my job easier! But you're right about the pattern- it had to be oriented that way. And I looked at that wire and it does need tweaking. You're not being picky at all, I ask for input because I want to improve. 😃 Thanks again! |
|
|
|
Post by 1dave on Mar 15, 2020 13:02:06 GMT -5
Not sure how you wrap this kind of triangle shaped cab, this is what I came up with. It actually hangs well but it makes the design tilt a little to the left. Any suggestions on how else I could have done it? Thanks for looking. Perfect doesn't have anything to do with balance. That is just an opinion. |
|
